Showing results: 1291 - 1305 of 2617 items found.
-
Thermal Engineering Associates, Inc.
Systems for determining relationship between temperature-sensing junction voltage versus junction temperature of diodes, integrated circuits and thermal test die. Provides internal current sources, voltage measurement to 1 mV, and temperature measurement to 0.1ºC. 16-channel capability with optional printer and serial port data output.
-
PCI-3127 -
CM Technologies Inc.
The PCI-3127 is a PCMCIA-form factor TDR that can be used to identify and locate failures in installed wiring and cable systems. The instrument can make high resolution TDR measurements on circuits up to 96,000 feet (~30km) from your Windows XP notebook computer or PC using a low-voltage non-destructive test signal.
-
5085 -
Abaco Systems Inc
ECM P/N 5085 provides two channels of 24 bit A/D conversion suitable for high resolution low speed applications, which include bridge circuits, thermocouples, RTD and voltage measurements. For bridge applications each channel provides a fused +5 Volt or a current source drive.
-
30056 -
Parallax Inc.
The Flexiforce sensor features a pressure sensitive disc pad on the end of an ultra-thin (0.008 in.) flexible printed circuit ribbon that can be easily integrated into force measurement applications. Note that the flexible ribbon is to accomodate optimal placement of the pressure-sensitive disc; the sensor does not measure force applying curvature to the ribbon itself.
-
GCP-MG -
proconX Pty Ltd
GCP-MG is a next-generation Modbus/CAN gateway specifically designed to interface Woodward's GCP-30 series genset controls (GCP-31, GCP-32), and LS 4 circuit breaker controls with Modbus networks. The GCP-MG gateway has been developed in cooperation with Woodward to ensure the highest possible degree of interoperability with Woodward equipment.
-
3270 Series (350V,1875W~22500W) -
PRODIGIT Electronics Co, Ltd.
3270 Series is suitable for the step, square and sine wave of the AC Power device test, especially for the uninterruptible power supply UPS, Inverter, fuses, circuit breakers, power regulator AVR, battery, AC / DC power supply / components ... and so on, absolutely is the best test solution in the market.
-
MAG-450 -
MCH Instruments Co.,Ltd.
Features:*Advanced circuit design with imported components ensure minimum accuracy deviation.*Signal frequency:100kHz~150MHz, 3 harmonic up to 450MHz*Output wave form:sine and amplitude-modulation wave*RF/AM output, max, intensity≥10Vp-p*External modulation signal can be set between 50Hz~20kHz
-
Meilhaus Electronic GmbH
This digital logic analyzer has basic functions, easy operation and a new way of measuring data for monitoring and measuring signals in digital information processes. Thus, the device allows the analysis and troubleshooting in digital systems, such as transmission delays to be analyzed and the result of the information processing of the digital circuit and bus technology.
-
72-6792 -
Tenma
*Electronically locates hidden cables gas and water pipes*Traces hidden ceiling joists and wall studs*Senses presence of mains power withut touching live wires*Locates breaks in circuits and cables*Identifies faulty plugs switches and sockets*Incorporates audio signal and indicator light
-
VM-10, VM-20 , VM-30 -
UDEYRAJ ELECTRICALS PRIVATE LIMITED
High Voltage Meters measure AC and DC voltages of up to 30kV with high accuracy. The meter input impedance is as high as 1000 M ohm, making the meter suitable for measurement of voltages of high source impedance circuits. Meters are compact and light weight and can be conveniently used as a calibration meter.
-
SFY027 -
Shanghai Launch Electric Co., Ltd.
Microcomputer automatic control, all keyboard operation, convenient man-machine conversation function, detector signal switch through the time of preparation proceduresHighly stable circuit control system to ensure a high reliability of the instrumentPerfect overheat protection for column box and detectorStorage in ten seconds the file of parameters analysisStopwatch
-
NI
The I²C/SPI Interface Device is a master or slave interface for inter-integrated circuit (I²C), or master interface for serial parallel interface (SPI) devices. With plug-and-play USB connectivity, the I²C/SPI Interface Device is a portable solution to communicate with consumer electronics and integrated circuits. The I²C/SPI Interface Device can be physically located more closely to I²C/SPI devices than PCI interfaces, reducing I²C bus length and minimizing noise problems. The I²C/SPI Interface Device supports I²C rates up to 250 kHz and SPI rates up to 50 MHz, and it also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I²C devices or toggling LEDs.
-
NTN -
FuG Elektronik GmbH
High efficiency Short circuit proof and unlimited operation with full current in short circuit condition voltage and current regulation with automatic and sharp transition; control mode indicated by LEDs Voltage and current setting with 10-turn potentiometers with precision scale; the adjusting knob can be locked 4 digit DVM for voltage and current (for table-top models) Sense terminals for the compensation of voltage drop on the load lines. The nominal voltage always refers to the output terminals Parallel and series connection possible Suitable for inductive and capacitive loads for 700 W nominal power and higher, limitation of inrush current on switching on Interlock loop to monitor the external load and internal loop as a standard for three phase units Elapsed-hour meter as a standard for three phase units
-
Pacific Millimeter Products
These waveguide bandwidth detectors use silicon beam lead diodes on a planar stripline circuit to obtain an extremely rugged and compact device. Most millimeter wave broadband detectors have very poor VSWR due to the difficulty in obtaining a good wideband impedance match to the diode. To overcome this problem, these detectors utilize two diodes and an internal matched termination and 3 dB hybrid as shown below. This circuit allows a VSWR of 2.0 or better over a full waveguide bandwidth for most of these detectors. Detectors for waveguides WR-8 and smaller use a single zero bias GaAs diode. The high sensitivity zero bias GaAs diodes can also be special ordered for use at lower frequencies when highest sensitivity is required.
-
ENVIROMUX-PT3-600 -
Network Technologies Inc
Monitors and reports voltage of any 3 phase circuit. Remotely detect blown fuses or tripped circuit breakers. Three 600 VAC inputs, three 4-20 mA outputs. Inputs and outputs isolated from one another. Frequency: 50/60Hz. Maximum primary current: 600 volts. Accuracy: ±0.25% F.S. @60Hz. Output: 4-20 mA. "Zero" adjustment for accurate 0 VAC reading, and "Calibration" adjustment for frequency and voltage level. Powered by the ENVIROMUX-S420MA-24V. Regulatory approvals: UL, CUL, CE. Requires two ENVIROMUX-S420MA-24V to monitor three phases. Caution: installation should be performed by qualified electricians only. Make sure electrical service is disconnected before making any electrical connections.